Chapter 1 Product Assembly and Disassembly
Note: Cut off power before disassembling or assembling the product.
Parts Name
Packing List
Main body assembly and disassembly
When installing the main body, insert the end of the mainbody into floorhead connector vertically until a "click" sound is heard. Ensure that the main body is tight and not loose. To remove the main body, simply press the floorhead release button and lift the main body upward. (Fig 1)
Battery pack assembly and disassembly
1. Hold the battery and slide down along the leading slot, press down until a “click” sound is heard.
2. Press the battery release button, pull battery pack upward to take it out. (Fig 2)
Note: No need to take out the battery unless it needs replacement.
Handheld vacuum assembly and disassembly
Insert the end of the handheld vacuum installed with the battery pack into the main body connector vertically until a "click" sound is heard. Ensure that the handheld vacuum is tight and not loose.
In this status, the product is used as a cordless vacuum and washer. To remove the handheld vacuum cleaner separately, simply press the handheld vacuum release button and lift it up vertically. (Fig 3)
Dirty water tank assembly and disassembly
To assemble the dirty water tank, locate the dirty water tank's bottom to the main body tray slot and then push the dirty water tank towards mainbody until a “click” sound is heard. To take out dirty water tank, hold mainbody with one hand and the dirty water tank handle with the other hand, press the dirty water tank release button with thumb, and pull dirty water tank out. (Fig 4)
Charging base assembly
Press the charging base upper towards the charging base lower as the picture show. After a "click" sound is heard and clips are located in the corresponding holes. Finally, put the tray into the charging base to complete the installation of the charging base. (Fig 5)
Machine charging and placement
Place the floorhead in an upright position, lift the machine, align the charging slot at the rear of the machine with the charging socket on the charging base, and gently place the machine into the charging base. To take out the machine, hold the handheld vacuum handle and directly pull the machine out of the charging base. (Fig 6)
Clean water tank assembly and disassembly
To remove the clean water tank, hold the clean water tank handle and pull it upward to remove the clean water tank. To install a clean water tank, place it on floorhead and press down until a "click" sound is heard. (Fig 7)
Brushroll assembly and disassembly
To remove the brushroll, remove the clean water tank first, and then press floorhead with one hand, rotate the brushroll end cap upwards with another hand, and remove the brushroll outwards. To install the brushroll, first align one end of the brushroll with the spline, push and rotate it to the bottom of the spline, and then rotate the brushroll end cap until a “click” is heard to lock the brushroll. Finally, install the clean water tank back on the floorhead. (Fig 8)
Chapter 2 Use of the Product
Note: Before use, please check whether the machine has power. If there is no power, please fully charge the machine before using it.
LED screen and instructions
Use of a stick vacuum and a washer
In the upright tilt state, press the on/off button, and the product start to work. The default mode is in Auto mode, press the mode button to switch among floor mode, carpet mode, and Auto mode, accompanied by a voice reminder. Press the on/off button again, the voice reminds "Machine turning off", the main motor will run for 2 seconds, the machine stops working. (Fig 9)
In Auto mode, the machine power changes automatically based on how much dirty water or dust is detected. And the LED light colour changes accordingly. The more dirty water or dust is detected, the more red lights. And the less dirty water or dust is detected, the more blue lights.
1. When cleaning carpet, please clean the floorhead first (refer to "Cleaning and Maintenance, Floorhead Cleaning" for details) and to deep clean carpet it is recommended to replace the carpet brush. (Carpet brush can be selected according to your own needs and sold at JIMMY distributors.)
2. When the battery level is lower than 20%, it cannot be switched to Carpet mode.
When the upright vacuum cleaner is working, press the water spray button, the auto water spray function is open by default. LED screen will show the auto spray indicator, and clean water will be sprayed to brushroll automatically. To turn off auto water spray function, keep pressing the self-cleaning button for over 3 seconds when the product is on. To turn on the auto water spray function again, keep pressing the self cleaning button for over 3 seconds when product is on. (Fig 10)
If the floor is very dirty, you can choose to spray more water on the floor by using manual water spray function to improve the floor washing effect. With the machine turned on, press the manual water spray button, spray mouth sprays fan-shaped water; release the water spray button to stop spraying water. The manual water spray function can be activated no matter whether the auto water spray function is turned on or off. (Fig 11)
Note:
1. The manual water spray button cannot be used with the on/off button or the mode button at the same time.
2. It is recommended to use carpet mode when there is heavy pollution or water stain.
3. When cleaning the carpet, please turn off the auto water spray function.
4. Please use the low-foam cleaning solution with this product for cleaning. Do not put the easy foaming cleaning solution into the clean water tank for use, otherwise more foam will be generated during use, which may penetrate into the machine and cause danger.
Product lay flat to vacuum function
When the product is laid flat to clean under furniture, working power will automatically drop. This is normal. When the product is laid flat, do not shake the product violently to prevent water entering the dust cup.
Use of a handheld vacuum cleaner
1. Take off the handheld vacuum cleaner and connect with the accessories needed. Press the on/off button. Display screen will light up. The default mode is floor mode. Press mode button to switch between floor mode and carpet mode. Press the on/off button again to turn off the vacuum cleaner, and display screen will extinguish.
2. Handheld vacuum cleaner can be connected to different accessories, like an upholstery tool, crevice tool, to clean different places. (Fig 12)
Aim the accessory to the handheld vacuum mouth and push upward until a “click” sound is heard. Push the button on the accessory to remove accessory from vacuum cleaner.
Note:
1. Other accessories, like pet brush or stretch hose, can also be bought from JIMMY local distributor if needed.
2. When the battery level is lower than 20%, the machine switches to the floor mode automatically.
3. Do not use a handheld vacuum cleaner and carpet brush to pick up liquid.
Product charging
Connect power cord to the power socket, put the stick vacuum cleaner to charging base to start charging.
Note:
1. Fully charge the battery pack before first use. Empty battery power before the second charge to ensure the life of the battery pack.
2. If the product is to be long idled, please charge it once every three months. (Please only use power cord supplied with the unit)
3. When not charging, please remove the charging base power cord from the power socket to prevent the danger of accidental touching.
4. If need to charge the battery separately, applicable charger can be bought from the JIMMY distributor.
Self-cleaning and hot drying function
1. Self-cleaning + quick drying mode (drying the brushroll): Under the charging mode, press the self-cleaning button to enter the self cleaning and quick drying mode. (Fig 13) After the self cleaning process is finished, the machine will automatically enter the quick drying mode. If the power is insufficient, the machine will automatically enter the quick drying mode after charging.
2. Self-cleaning + full path drying (drying the suction port, brushroll, air path, HEPA, dirty water tank, etc.): Under the charging mode, press and hold the self-cleaning button to enter the self-cleaning and full path cleaning mode. After the self-cleaning process is finished, the machine will automatically enter the full path drying mode. If the power is insufficient, the machine will automatically enter the full path drying mode after charging.
Note:
1. Please put the tray into the charging base before starting the self-cleaning mode. Do not activate the self-cleaning mode without the tray.
2. The machine will clean the air path and the floorhead brushroll under the self cleaning mode.
3. Before start self cleaning, please drain the dirty water tank and make sure the product is placed on charging base, the power cord is connected to power socket and the charging base, and there is at least 50% water in clean water tank. After self-cleaning, please clean dirty water tank again.
4. When the power is lower than 15%, the machine cannot enter the self-cleaning mode or hot drying mode. After charging for a period of time, it can work on self cleaning mode or hot drying mode.
5.To stop the self-cleaning process, press the on/off button or the mode button, and then the machine will automatically go back to the charging mode. (Fig 14)
6. After the self-cleaning process is finished, the machine will automatically enter the hot drying mode.
Clean water tank empty indicator
1. During use of the stick vacuum and washer, if the LED screen shows "
" and the voice reminds "No clean water, please fill water", please fill clean water into the clean water tank and then continue to use directly.
2. During self cleaning, if there is no water inside the clean water tank, the self washing automatically stop and the voice reminds "No clean water, please fill water". Please fill clean water into the clean water tank and then press the self-cleaning button again to restart self cleaning.
Fill up the clean water tank
Fill up the clean water tank: After removing the clean water tank, open the water filling plug, flip it upward to expose the water inlet hole, pour clean water and cleaning solution in, and then plug it back to the original position and reinstall the clean water tank to floorhead. (Fig 15)
Note:
When adding clean water, you can add the JIMMY cleaning solution equipped with the product; the ratio is about two bottles of cleaning solution to one full water tank, the water temperature cannot exceed 40°C.
Dirty water tank full indicator
1. When the stick vacuum and washer detect that the dirty water tank is full, the machine will stop working and give a voice reminder. Please clean the full dirty water tank and put it back before use.
2. When it is detected that the dirty water tank is full in self-cleaning mode, the machine will stop working and give a voice reminder. Please clean the full dirty water tank and put it back, and repress self clean button to restart self cleaning.
Dirty water tank cleaning
Take out the dirty water tank upper cover and filter frame, dump the dirty water, assemble the dirty water tank after washing, and put it back to the main body. (refer to Cleaning and Maintenance of dirty water tank" for details)
Brushroll stuck indicator
When the cleaner is in vacuuming or self-cleaning mode, if the brushroll is stuck, the machine will stop and give a voice reminder. Please take out brushroll, clean the foreign matter attached to the brushroll or the hair winding on the brushroll, and reassemble the brushroll into the floorhead to resume working.
Brushroll cleaning
After removing the clean water tank, pull out the brushroll, use the blade on the mini brush to cut the hairs winding on the brushroll, and clean the foreign matter attached to the brushroll and floorhead. Install the brushroll and the window back. (refer to "Cleaning and Maintenance of Floorhead Assembly" for details)
Air path blocked indicator
1. When the stick cleaner is in working or self-clean mode, if the air path is blocked, the machine will stop working and give a voice reminder. Please clean possible blocked areas like the handheld vacuum dust cup, nozzle air path, dirty water tank in sequence. After cleaning, restart the machine to work.
2. When a handheld vacuum cleaner is working, if the air path is blocked, the cleaner will automatically stop. At this time, the dust cup and HEPA need to be cleaned.
Air path cleaning
Disassemble the dirty water tank, take out the dirty water tank upper cover and garbage basket, wash all parts, and then assemble it back. Use a cleaning brush to clean the dirt, foreign objects and hair inside the air path of floorhead. Put the dirt water tank back into mainbody.
Remove the dust cup, then take out cyclone, empty the dust cup, remove the HEPA, clean all parts and reassemble the dust cup. (Refer to "Cleaning and Maintenance" for details)
Voice reminding function
The product includes voice reminding of 6 different languages: English, German, Italian, French, Polish, and Russian. Voice of the new machine is turned on and in English by default, press the voice button to switch to other language. Keep pressing the voice button to turn off the voice function; press the voice button again to turn on the voice function. (Fig 16)
Note:
When the product is used as handheld vacuum cleaner or a stick vacuum cleaner, there is no voice function.
Battery low power indicator
1. When the stick cleaner is working, if the voice reminds "Low battery. Please charge the battery". Please use it
after charging.
2. When the stick cleaner is working, if the voice reminds "Low battery. Machine will be turned off soon. Please charge the battery", the power is about to be exhausted, and it will automatically shut down. Need to charge for use.
3. When using vacuum cleaner, the icon on the LED screen displays left working minutes. When battery power is lower than 20%, the battery icon in the top right corner turns from white to red.
Chapter 3 Cleaning and Maintenance
Dirty water tank cleaning
After turning off the vacuum cleaner, remove the dirty water tank, lift the water tank top cover, remove the filter frame from it, open the flip cover of the filter frame, and take out the filter. Pour out dirty water and dirt in the water tank, then wash dirty water tank, the water tank cover, the filter frame, and filter. If there is foreign matter in the dirty water tank pipe, it can be cleaned with cleaning brush; dry the above parts after washing. And then reassemble all the parts back into the dirty water tank. Put dirty water tank back into the main body to continue working. (Fig 17)
Note:
1. After using stick vacuum cleaner, it is recommended to clean the dirty tank immediately;
2. When reinstalling the garbage basket, do not fold the black soft rubber under the filter.
Floorhead cleaning
After removing the clean water tank, brushroll, and dirty water tank, insert the cleaning brush through the circular hole below the installation position of the mainbody to clear foreign matter and scales in the pipe, and the clogged hair; Use the blade on the mini brush to cut off the entangled hair on the brushroll; Wipe the dirty parts of the machine and then assemble them back into machine (the brushroll can be placed in the brushroll housing for drying). Wash the cleaning brush and then put it back into the brushroll housing. (Fig 18)
Note: Do not wash the floorhead with water!
Tray cleaning
Remove the tray from the charging base for cleaning. Once it’s dry, reinsert it for use. (Fig 19)
Note:
Please do not wash the charging base!
Please do not activate the self-cleaning mode if a tray is not installed on the charging base!
The charging base is not waterproof without the tray
Dust cup cleaning
Press the dust cup release button to remove the dust cup from the handheld vacuum cleaner. Lift the metal handle on the cyclone to pull out the cyclone assembly and empty dust cup. Hold the metal handle and rotate to remove HEPA. (Fig 20)
Maintenance and Storage
1. it is recommended to clean the dirty water tank, dust cup, and brushroll after each use. If any of the following situations:
1) HEPA filter leaks dust.
2) Foam filter severely damaged.
3) The brushroll has serious hair loss, or has strong vibration and abnormal noise during use.
2. It is recommended to purchase consumables and replace them to avoid machine performance.
3. When the machine is long idled, place it in a cool and dry place, avoiding direct sunlight or a wet environment.
When packing and storing the machine, please be sure to clean the machine and dry all parts to prevent damage to the machine.
